VCE405RA211-LV000资料

Connectivity Engine VCE405Technical DataThe VCE405 Connectivity Engineprovides a flexible off-the-shelfmethod for quickly developingand deploying cost-conscioushigh performance custom sys-tems.The low power consumption ofthe powerful, 375+ MIPS, IBMPowerPC 405GP and the ALMA2PCI/VME bridge make theVCE405 well-suited to criticalenvironments such as medicalor aerospace applications.transfer overhead and minimizes pipelinestalls to greatly improve performance.The general architecture of the 405GPconsists of a 64-bit, 133MHz ProcessorLocal Bus (PLB) and a 32-bit, 44MHzOn-Chip Peripheral Bus (OPB).High performance peripherals attach tothe PLB and less performance-criticalperipherals attach to the OPB.8MB Flash EPROMIn addition, the board provides oneFLASH memory array which is composedof two, equal-sectored, Intel 28F320-J5a-110, 2M x16 Flash EPROM's for atotal of 8MB. Each EPROM has thirty-two, 128kB blocks, but since theEPROM's are concatenated to form a32-bit data path, the paired EPROMblock size is 256kB. Thales Computersuses the lowest addressed blocks for itstest and boot software, and for storingthe EPROM's programming algorithm.These blocks are then locked into thearray so they cannot be accidentallyerased or overwritten. The FlashEPROM array may optionally be populat-ed with Intel 28F640J5a-120 (4M x16)devices to provide 16MB respectively.➜Real Time ClockThe Real Time Clock (RTC) function isprovided by a Dallas SemiconductorDS1602 Elapsed Time Counter. Thisdevice can keep track of over 125 yearsworth of seconds in each of its 32-bitcounters. One counter runs continuous-ly. The other counter counts secondsonly while +5V is active. Software candetermine how long the RTC has beenrunning on battery power by subtractingthe VCC active counter from the contin-uous counter.UVEPROM socketThe board also provides a 32 pin DIPsocket for a 27C801 8Mbit (1MB)UVEPROM. The UVEPROM may be usedto provide the initial boot code for theFlash EPROM and then be removed.➜PowerPC 405GPThe IBM PowerPC 405GPTMis a 32-bitRISC embedded controller. High per-formance and peripheral integration ofthe 405GP make the device ideal forwired communications and other perva-sive computing applications.The 405GP is powered by a PowerPC405B3 embedded core. This core tight-ly couples a 266MHz CPU, MMU,instruction and data cache (16kB I-cache; 8kB D-cache), and debug logic.This finely-tuned core reduces data➜Memory64 or 128MB SDRAM The system memory consist of twobanks of 32MB or 64MB each makingrespectively 64MB or 128MB of syn-chronous DRAM with Error Control andCorrection. The SDRAM is directly con-trolled by the processor using a 32bit/133MHz bus.Compact Flash SocketA Compact Flash module can be fitted tothe on-board plug-in site to give up to1Gbytes of field removable storage.➜Serial EEPROMThe board provides a 64K-bit serialEEPROM, a Fairchild part # NM24C65Uor equivalent, with an IIC interface. TheEEPROM hooks directly to thePPC405GP IIC bus lines.➜Ethernet InterfaceThe board provides 100Base-TXEthernet, with auto-negotiation to10Base-T when connected to networksnot capable of 100Mbps operation.Ethernet support through the MediaAccess Control (MAC) layer is providedin the PPC405GP chip. The PhysicalLayer Device (PHY) and the PhysicalMedium Dependent sub-layer and inter-face (PMD) are provided on board. Theconnections between the MAC and thePHY conform to the MediumIndependent Interface (MII) specification.The supported media is Category 5Unshielded Twisted Pair cable (UTP),accessed via an RJ-45 connector on thefront panel (convection cooled).The Ethernet media access con-troller of the PPC405GP is ageneric implementation of theEthernet Media Access Control(MAC) protocol complying withANSI/IEEE Std 802.3 and IEEE 802.3usupplement. Its major features are:•Dual speed (10/100 Mbps)CSMA/CD (half-duplex) and full-duplexEthernet MAC complying withANSI/IEEE Std. 802.3 and IEEE802.3u supplement•Independent, large (2kB) transmit and(4kB) receive FIFOs with programma-ble thresholds to minimize overrunsand underruns•Unicast, multicast, broadcast, andpromiscuous address filtering capabili-ties.•Two 64-bit hash filters for unicast andmulticast packets•Automatic retransmission of collidedpackets•Compliance with IEEE 802.3x stan-dard packet-based flow con-trol, including self-assem-Optionalbled control pause packetATX ComplianttransmittingPower Supply•Support for VLAN tag ID incompliance with IEEE Draft802.3ac/D1.0 standard•VLAN tag insertion or replace-ment for transmit packets is a pro-grammable option•Wake on LAN (WOL) handlingPlease ask Thales Computers for thesupport of this feature.PlugVMEbusVMEbus P1 (5-row)Ethernet10/100(RC version)Dual Async.Serial LinesRS232I2E BusFour Sync./Async.Serial LinesRS232/RS4222/RS485VMEbus P2 (5-row)P0ALMA 2PCI/VMEBridgePCI 64PCI 3264 MBSDRAMI/O on P2DualESCCDualESCCPowerPCIBM 405 GPCPU8 MBFLASHCompact FlashSocketAsynchonousSerial LineEthernet 10/100(convection cooled versions)Connectivity Engine VCE405 block diagramvides dual independent full-duplex asyn-chronous channels with no handshakingcapability and with software selectableRS-232/422/485 transceivers (ports2 & 3). All the 4 serial lines are availableon the software selectable RS-232/422/485 transceiversEvery ESC Controller features:•Dual full-duplex channels•Ability to accommodate a crystal oscil-lator, baud rate generator, and digitalphase-locked loop on each channel•Multi-protocol format (asynchronous,monosyncchronous, bisyncchronous,SDLC/HDLC, SDLC/ HDLC loop)•Encodes in the following modes: NRZI,FM0, FM1, and Manchester•CRC-16 or CRC-CCITT error detection•4-byte transmit FIF0/8-byte receiveFIF0➜Dual AsynchronousSerial LinesThe PPC405GP provides two asynchro-nous 16550 compliant, RS-232 serialports (0 and 1). Port 1 is available onthe front panel and on the P2 connector,and port 0 is available on the P2 con-nector. Serial port 1 features a 2-wireinterface (Tx,Rx,GND) while Serial Port 0features a full modem interface(Tx,Rx,DCD,CTS ,RTS,GND).➜IICbus portThe PPC405GP provides an inter-inte-grated circuit (IIC) bus interface which isavailable to the users on the backplane.The IIC bus is a 2-wire, bi-directional,open-drain, low-speed serial interface.The serial clock (IICSCL) and serial data(IICSDA) lines are bidirectional, to sup-port multiple bus masters and to mixhigh- and low-speed devices on the samebus. The IIC interface is compliant withhe Pillips semiconductors IIC specifica-tion, dated 1995.It supports the follow-ing standard and enhanced features:•100-kHz and 400-kHz operation•8-bit data transfers• 7-bit and 10-bit addressing• Slave transmitter and receiver• Master transmitter and receiver• Multiple bus mastersThe IIC interface can switch between 7-bit and 10-bit addressing under programcontrol.➜Quad SynchronousAsynchronous SerialLinesTwo enhanced serial communicationscontrollers (ESCC) from Zilog, Z85230-16 provide for synchronous/asynchro-nous serial lines at data rates up to3.6Mbit/sec. One controller providesdual independent full-duplex synchronousor asynchronous channels with softwareselectable RS-232/422/485 trans-ceivers (ports 4 & 5). The other pro-➜Low Power VMEInterfaceManaged by the IBM/Thales ComputersALMA2 PCI to VME bridge componentthat provides a highly integrated lowpower single chip solution:•VME to PCI 64bit/66MHz•VME and IEEE-STD-1014-1987 com-pliant (32-bit) with VME64 capability•VMEbus system controller•VMEbus requester (Level 1-4)•VMEbus interrupter and interrupt han-dler (IRQ1-7)•VME transfer rate up to 70 MB/sec•VMEbus master/slave A32, A24,A16: D32, D16, D8, UAT•VMEbus master/slave A32, A24:D32BLT, D64MBLT•Programmable VME slave image baseaddress and size (8 VME slave chan-nels)•VME to PCI access conversionthrough 8 MB granularity mappingtable•Transmit/Receive FIFOs•Programmable posted write, prefetchread, coupled mode•Programmable BB2BLT mode: map-ping of multiple single PCI accesses toa VMEbus BLT/MBLT cycle•Semaphore registers•VME/PCI 2 channels DMA controller➜User PCI InterfaceThe VCE405 features a twin 64-bit PMCsite suitable for connecting IEEE1386.1standard PCI Mezzanince Cards (PMC).The PCIbus supports either 3.3V or 5VPCI signaling. The default manufacturingPCI signaling key setting is for 3.3V use,but can be modified by the user in orderto support 5V only signaling PMC. Careshould be taken for coherent signalinglevel on the PCIbus. •PMC #1 routes the first 46 of its 64I/O line via J14 to P2 rows D and Z,and the remaining 18 I/O lines arerouted via P0. •All of PMC #2's 64 I/O lines are rout-ed to P0 via J24. ➜Remote Panel ExpansionPortIn order to ease the integration of theConnectivity Engine into an enclosurewhere the board’s front panel may notbe visible or conveniently accessible, a10-pin header providing the means toconnect a remote front panel with 5LEDs and Reset/Abort is provided.➜MiscellaneousRelated Products•Board size: VME double Eurocard (6 U- 233.3 mm x 160 mm)➜•Single VME slotSoftware•Power requirements: The Tornado/VxWorks Board Support+5V (+5%,-2.5%): 1.5A; Package (BSP) is available in accordance+12V for flash memory programmingwith the WindRiver’s Winlink partnershipand PMC siteprogram.-12V for PMC site only•Weight: 370g in RC version ➜Rear Panel Connections•Conduction cooled version (RC) is IEEE1101.2-1992 compliant and is a sin-In order to ease the use of the I/O avail-gle VME slot solution.able on the backplane, ThalesComputers has designed a rear-panel•Electromagnetic compatibility:board.NF EN 55022 Class BNF EN 50082-2The VCE405 supports various bootoptions such as boot from Ethernet or•All Thales Computers SBCs are ECboot from CompactFlash disk.Softwarecompliant.support of the synchronous serial linessuch as SDLC, bisynchronous and IICCustomers’slave mode are not included in the BSP.Services➜Quality AssuranceThales Computers' ISO 9001 certifica-tion is just another way for us to backThales Computers' commitment to quali-ty products and customer service.➜WarrantyAll of Thales' hardware products are cov-ered by a twelve month return-to-factorywarranty.➜PMCWhen the Connectivity Engine does not➜Support Servicesfully provide all the features required byThales Computers offers a standardyour system, COTS PCI Mezzanine cardsSupport and Service program whichare likely to fill the missing gap at theincludes update services, hotline access,best price/performance point. Thalesproduct repair and exchange services,Computers also markets an extensiveon-site or remote technical assistance,choice of COTS PCI Mezzanine Cards forPre-planned program technology inser-Commercial grade or Harsh environ-tion (P3I) and long-term support (overment: Networking (Ethernet, ATM), addi-15 years). Moreover, Thalestionnal serial lines, Parallel I/O,Computers’s structure is flexible enoughGraphics, etc...to provide custom support such asfrozen configurations.➜Derived DesignsLeveraging more than 15years of new product develop-ment and customer support inembedded and rugged comput-ers, Thales Computers hasbeen selected for deriveddesigns based on its domainsof excellence : PowerPC, Real-Time and Unix OS. AndPCI/PMC technology.VCE405 Technical FeaturesENVIRONMENTAL SPECIFICATIONSConvection CooledSATemperature rangeOperatingStorageConformal CoatingRelative Humiditywithout condensationShockSine VibrationOperatingRandom VibrationOperating0.01g2/Hz 10-40Hz 0.1g2/Hz 5-1000Hz0.0007g2/Hz 100-200Hz 6dB/octave roll-off0.00005g2/Hz 2000Hz from 1000 to 2000HzAltitude15000 ft15000 ft33000 ft50000 ft2g 20-500Hz2g 20-500Hz5g 32-2000Hz5g 32-2000HzOperatingNon-operating90%10g/16ms20g/11ms90%10g/16ms20g/11ms95%40g/20ms40g/20ms95%40g/20ms40g/20ms0°to +55°Cflux m/s (*)-45°to +85°COption-45°to +85°CYes-20°to +65°C-40°to +75°CFlux m/s (*)-45°to +100°CYes-45°to +100°CYes-40°to +85°CWARAConduction CooledRCNatural Convection Enabled: No fan required.The VCE405 has been designed for being used in naturel convection environments.It has been successfullytested in a fanless chamber at up to 65°C.Please contact Thales Computers.➜VCE405 Order CodeSAEnvironment ClassStandardXXXXXXXXXOptionXXXXXXXDefault on RAXXXXXXXXDefaulton RCRARCCodeSARARC2121--VLVVCE4052 1 - OOO

Rugged Convection CooledRugged Conduction CooledProcessor Speed266 MHZSDRAM Memory64MB128MBFlash8MBEthernet Link Front panelRear I/O on P2FirmwarePre-boot VxWorksPowerPC BootCoatingThe VCE405 is delivered without Compact Flash Card➜Developer’s kitwhich includes the rear panel board ant the rear I/OcablesCP2P0-VxWorks-BSP-VCE➜VxWorks BSP for VCE405 Order Code: Thales Computers, The Ruggedizer and PowerEngine are registered trademarks of Thales Computers S.A. PowerPC, IBM are registered trademarks of IBMCorp. LynxOS is a registered trademark of LynuxWorks, Inc. AltiVec is a registered trademark of Motorola, Inc. TORNADO and VxWorks are registered trade-marks of Wind River Systems, Inc. UNIX is a registered trademark licensed exclusively by X/Open Company Limited. All other product names, trademarks andregistered trademarks are the property of their respective holders.

Corporate Headquarters150 rue Marcelin BerthelotZI Toulon-Est • BP 24483078 Toulon Cedex 9FranceTel.: +33 - (0) 4 98 16 34 00Fax: +33 - (0) 4 98 16 34 01International SalesDepartment67, rue Charles-de-Gaulle78350 Jouy-en-JosasFranceTel.: +33 - (0) 1 39 56 72 72Fax: +33 - (0) 1 39 56 72 70USA Headquarters1203 New Hope RoadRaleigh • NC 27610USA Tel.: +1 - (800) 848 2330+1 - (919) 231 8000Fax: +1 - (919) 231 8001United KingdomCornwell Business Park31 Salthouse Road • BrackmillsNorthampton • NN4 7EXUnited KingdomTel.: +44 - (0) 1604 700 221Fax: +44 - (0) 1604 700 112www.thalescomputers.comWith ISO 9001 Certification, Thales Computers guaranteesISO 9OO1Total Customer Satisfaction.Reference CA.FP.074-1e • July 2002 • The specifications are subject to change without prior notice •Photographs: Thales Air Defence, ZEDDA/DCN • Copyright Thales Computers 2001